STARTUPBIZHUB

“Start Your Own Flour Mill”
Comment Page 2

  • Amit Sharma expert adviser said on April 20, 2011
    @Raghunath rao, You can't start a Flour Mill with Rs. 5 lakhs. Maida Flour Project needs Rs. 2.5 Crores and above.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • amit kumar said on April 22, 2011
    I want to open wheat flour mill.So for the same i want each and every details like:
    1. Estimated cost in setting up mill depending on yield like low cost high yield.
    2. land required.
    3. market for availability of raw material i.e Wheat
    4. purchasing of machine .
    5. requirement of labors etc.
  • Amit Sharma expert adviser said on April 22, 2011
    @ amit kumar,
    1. Estimated Cost for Roller Flour Mill( 4 Ton/Hr) = Rs. 2.5 Crores 2. Land Required = 1 Acre.
    3. Availability of Wheat = Depends upon the location.
    4. Purchasing of Machinery = Consult the Milling Technologist.
    5. Requirement of Labour = 21 For Operation and 25 For Loading, Unloading and Packing.
    Hope the details are clear.

    Chakki Fresh Whole Wheat Atta Plant
    1. Estimated Cost for ( 2 Ton/Hr) = Rs. 80 Lacs
    2. Land Required = 0.5 Acre.
    3. Requirement of Labour = 12 For Operation and 20 For Loading, Unloading and Packing.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • shailender goyal said on April 23, 2011
    Dear sir, we saw your answering about above mentioned queries. we want to establish a commercial flour mill near alwar distt.-rajasthan..i need ur help for such plant..here we saw a wide scope because here consumption ratio is very high..so can u send a project report about 1/2 tones /hr.
  • Varun agrawal said on April 24, 2011
    Amit Sir pls. Guide me for the complete details for 2tan/hr chakki plant business location: Aligarh (up) varun.aligarh@gmail.com 9012011597 is there any option for 1tan/hr plant with optimum production cost
  • Amit Sharma expert adviser said on April 25, 2011
    Dear shailender goyal, Setting up a Flour Mill in Alwar is good decision as Govt. has revoked the taxes from wheat products, secondly Alwar is located very near to many districts of Uttar Pradesh where the cost of Wheat is quite less than other states like Rajasthan, Haryana or Delhi. If you want to produce chakki fresh atta the feasible capacity is 2 Ton/Hr and If you opt for Roller Flour Mill the feasible capacity is 4 Ton/Hr. For costing of these projects you can refer my previous comments Posted here. 1/2 Ton/Hour Roller flour mill is neither available nor recommended, And 1/2 Ton/Hr Chakki Plant is not Feasible.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Amit Sharma expert adviser said on April 25, 2011

    Dear Varun agrawal, Aligarh is good place to setup a chakki plant as the arrival of wheat and consumption of atta both are good. Aligarh is also best for Roller Flour Mill because of wheat products like Maida, Superfine Atta are mostly consumed in muslim areas. For the project setup and cost you may refer my previous comments.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • hukam chander said on April 25, 2011
    I want to start a atta chakki plant in uttarakhand. so pls give me the detail of atta chakki plant. about machine, power, cost etc. i want to start 1 ton/day.
  • SSEJJEMBA SSONKO said on April 27, 2011
    i need to open up a maize mill in UGANNDA, WAKISO DISTRICT SANGA VILLAGE. Please send me all the necessary information needed. costs, background of machine, power needed, types ,shipping etc. ssejjemba ssonko. +256772356459
  • Alvin Advin said on April 28, 2011
    sir, if i start with install a smallest unit for flour mill what is the cost because i am very new for it. Once it started and than i knew all up and down in this field i believe that we should take practical. I stared flour mill in delhi what is your suggestion
  • Abhijit Shah said on May 1, 2011
    i want to start a roller mill in tal.shirpur. maharashtra. about 10 MTPD plz sent a project report accordingly. and what are subsidies for that
  • Ranjeet Sethi said on May 3, 2011
    Dear Mr.Amit Sharma... Can you please detail regarding the subsidy offered in Madhya Pradesh for setting up a Flour Roller Mill with an investment of 2 crore excluding land...Thanks
  • Amit Sharma expert adviser said on May 3, 2011
    Ranjeet Sethi, For the subsidy from central Govt. you can contact Minstry of Food Processing Industries, Panchsheel Bhavan, August Kranti Marg, New Delhi-110 049, Phone: 011-26492475. And for the Subsidy provided by Madhya Pradesh you can visit this link http://www.mptrifac.org/PotSector/SProjectProfiles/Agri%20&%20Food%20Processing%20-%20Roller%20Flour%20Mill%20Project.pdf

    or you can contact Head Office : MP Trade & Investment Facilitation Corporation Ltd., AVN Tower Mezzanine Floor, 192, Zone-1, M.P. Nagar, Bhopal-462011. Madhya Pradesh (India), Tel.:(91)755-4270246 E-mail : trifac@mptrifac.org

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • syed husain akbar said on May 3, 2011
    kingly tell me the scope of margin in flour mill. i want to set up a mill near moradabad, so kindly me some opportunities & threats for the same and cost of the project
  • silvester ommwenga tirimba said on May 4, 2011
    nairobi city,kenya in africa kindly send me the costs of a second hand mill producing 150 tonnes per day and any other requirements by buhla millinh company in italy
  • Sunil M said on May 9, 2011
    Hello Sharmaji, I have one question for you why is it so that the Atta that is made from the traditional chakki Machine smells good and makes good Rotis and on the other hand the Rotis that are made from the Readymade Atta, from these big players (ITC,Pillsbury, etc) taste so average.
  • Amit Sharma expert adviser said on May 10, 2011
    Because in MNCs like ITC/Pillusbury we dampened and conditioned the wheat before grinding and remove the Bran ( Fibers) before packing. Aroma ( Smell ) of Stones is more when we grind dry wheat and Taste is more better when we eat atta with more fibers. Local ChakkiWala in streets grinds the whole dry wheat which creats more aroma and taste. Because you get 100% Bran in that atta.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Rajiv Tyagi said on May 12, 2011
    Hi! Mr. Sharma, I'm starting a chakki plant in Ghaziabad with a capacity of 4MT/Hr. Building and machinery are ready , only installation is left at the moment.At this stage what all you suggests best for me i.e., marketing ,purchasing and precautions etc.Yet no loan is there but in future we need it for working capital,advice me the best the amt. of loan, subsidy etc. Waiting anxiously.
  • Dr.Ramprasad Shelke said on May 12, 2011
    I wants a information about advance technology flour mill. its total estimate and project cost with how much working capital i want? Marketing source ,subsidy.
  • Amit Sharma expert adviser said on May 19, 2011
    @ Ramprasad and Brijpal , All the details are provided in previous comments. Read all comments posted here.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • parmeshwer Gupta said on May 20, 2011
    Dear Sir I want to know the process of Small scale flour mill & give the Brief Information to start In Bahraich .
  • afzalbaig said on May 21, 2011
    i need complete details about flour mill, how much project cost and how much i need working capital.
  • avinash tiwari said on May 21, 2011
    i am looking to set up 2ton/day wheat flour mill at khurai m.p what will be the total cost to set it and how much workers are needed for it? this can be financed? if yes and the total cost exceeds 25lacs then what will be the subsidy of govt.? please provide me the details thanks
  • Amit Sharma expert adviser said on May 21, 2011
    @Tushar, This is not the right place to advertise your products, Startupbizhub.com is the platform to help the investors planning to start a business , it cannot be used as a B2B portal. Thanks for understanding. Post will be removed as soon as the Moderators review it.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Amit Sharma expert adviser said on May 21, 2011

    @Avinash Tiwari, The feasible capacity to start a Flour Mill ( Chakki Fresh Atta Plant) is 2 Ton/Hour and All the details about this are provided in my previous comments.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • vivek said on May 25, 2011
    Dear sir i would like to start a business in west bengal or any 2nd sale flour mill for sale around west bengal. i am interested.
  • MUSTAFA GERIMA said on May 25, 2011
    I am expecting to start my cereal milling and processing business in Arusha Tanzania starting with maize milling and later on rice processing. my working capital as per now is Tshs 6.4 billion i'm looking for funding sources
  • Shahid said on May 25, 2011
    I have a small land and would like to setting up a flour mill in my area. Can you guide me from where I can get machinery and other support in this field. My capital is 20 Lac BD Taka: US# 30,000.
  • Amit Sharma expert adviser said on May 25, 2011
    @Vivek, Second Hand Flour Mill is not recommended in this competitive market, you better start a new flour mill.

    @MUSTAFA GERIMA, Whats your desired capacity to start Maize Milling ?

    @Shahid, You cant start a good flour mill with the capital of $30,000. You need atleast $ 2,00,000 to start this business.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Amit Sharma expert adviser said on May 27, 2011
    @Nirmal Sen, A single chakki can grind 3 Qntl/Hr wheat, You dont need to setup a mill for that. Go to local market and buy a chakki, Install it and grind the wheat.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Piyush Chouhan said on May 29, 2011
    Hello, Mr. Sharma. I want to setup a wheat flour mill in Indore. is 10ton/day production capacity is sufficient at initial level? is 90 lac rs. is sufficient to establish new plant.
  • Amit Sharma expert adviser said on May 29, 2011
    @Piyush Chouhan, You can Start the Flour Mill ( Chakki Fresh Atta Plant) Capacity 2 Ton/Hr with Rs. 90 Lacs. 10 Ton/Day is not the feasible capacity.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • ashish said on June 10, 2011
    hello mr. sharma i want to set up a roller flour mill with 60 ton capacity/day. what will be the whole estimated cost of automatic plant with building ?
  • rajesh khetan said on June 11, 2011
    dear AMIT JEE i'm from patna BIHAR. i'm interested in starting a flour mill. please guide me how can i get maximum output in minimum investment.
  • Faizan Ahmed Qureshi said on June 11, 2011
    I want to open flour mill for this i want project report or want to know how to establish and how to be bank provide loan against this project. Am be open this mill in village sonkach small village near bhopal (30km) far away from bhopal (MP)
  • Amit Sharma expert adviser said on June 11, 2011
    @Ashish, You have to setup the Flour Mill with the capacity of 4 Ton/Hr. Project Cost is Rs. 2.5 to 2.7 Crores. All other details about this project are already posted in my Previous Comments here.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Amit Sharma expert adviser said on June 11, 2011

    @Rajesh, First Decide the Capacity of plant. And to get the maximum output with minimum investment  you must meet a Well Experienced Flour Milling Technologist who can customize your plant as per your requirement. Feel free to ask any query here.

    @Faizan Ahmed Qureshi, All the basic and important details are already provided in this article, I request all the users " Please read the article and all the comments posted here before asking a question , replying to same question again and again is not easy as it increases the page load time for slow net users and number of spams as well. if you have any other doubt  which has not been answered here, feel free to post here.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • vikas jain said on June 12, 2011
    i m in jaipur want to make career in flour mill business. pls guide accordingly.
  • Amit Sharma expert adviser said on June 12, 2011
    @vikas jain, How much can you invest ?

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • malebohang zwakala said on June 14, 2011
    where to get machinery for flour mills and at what cost? my location is lesotho in mafeteng district
  • Agrkulture Foods said on June 14, 2011
    Dear Sir, I tried contacting you this morning. We are willing to buy 5MT/day of quality flour from your clients/new setup coming up in Haryana especially in Gurgaon and neighboring areas. We are food processing company based out of Gurgaon, HR, India. Kindly email if someone has setup a plant and wants to sell. agrkulture@gmail.com
  • Amit Sharma expert adviser said on June 15, 2011
    @Agrkulture Foods, None of our client is willing to sell their unit. Secondly all the units have the capacity of more than 100 Tonnes/day.

    @malebohang zwakala, First decide the capacity of plant.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Ahmed Alzaidi said on June 16, 2011
    Hi I am from Tripoli,Libya and i would like to start a large scale flour mill,so i need to know where can i get the flour mill machinery,How much it will cost,and every thing that you think will help me to set up the business.. many thanks
  • Pradeep Katke said on June 21, 2011
    I would like to start rava,besan,atta chakki in Kolhapur District Maharastra, i am not aware of the process so can you guide me in same.
  • Amit Sharma expert adviser said on June 21, 2011
    @Pradeep Katke, To Start A Rawa Plant you have to setup a Roller Flour Mill with Chakki Plant. Minimum Feasible Capacity for this Plant is 100 Tonnes/Day. And the Project cost is Approx 3 Crores. You have to setup the individual plant to produce Besan. If you want to produce besan from chana dal then the feasible 1 Ton/Hr Plant cost is Approx Rs. 1 Crore. And if you want to besan from Raw Chana then the project cost is Rs. 2 Crores.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Jack said on June 22, 2011
    I want to know about spices processing plant.what is the approximate capital investment required for starting a Spice processing business in Assam. Is there any practical training available in anywhere in India. please advise detail information.My mail Id is (jackdawsan0@gmail.com).Thank's.....
  • aditya prasad mallick said on June 22, 2011
    I am interested to know what is the price of small flour machine , where and how i will get it please guide me .I want to start a small flour mill.
  • Amit Sharma expert adviser said on June 22, 2011
    @Jack, Investment depends upon the type of plant you want to setup. If you want to process any particular Spice then the project cost will be less But if you want to process all the spices like Turmeric Powder,Chilli Powder,Coriander Powder,Mix Spices, Etc. then the project cost will be higher. And you also have to decide the Capacity of plant. We'll surely help you about spice processing if you clear out these things.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Amit Sharma expert adviser said on June 22, 2011

    @aditya prasad mallick, Small Flour Mil Project Cost is Rs. 70 Lacs.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Amit Sharma expert adviser said on June 23, 2011
    @deepak thora, 2TPH Chakki Atta Plant Project cost is Rs. 70 lacs Including Building, Godowns, machinery and electrical. Before buying the machinery you have to hire a Flour Milling Technologist who will design your plant and provide you the detailed Engineering.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Jack said on June 26, 2011
    Thank's for your advise. Sir, i want to set up an basic small scale Assam Bhoot Jolokia (spice) processing plant. I do have adequate numbers of suppliers of Bhoot spice. Give me some advice about what short of capital investment,Land,initial business concerning steps....etc..etc.Please give me details about the plant related information........thank's again....
  • Amit Sharma expert adviser said on June 27, 2011
    @Jack, Bhut Jolokia ( Ghost Chili or Ghost Pepper)is used for homeopathic preparations as its a good remedy for summer heat. its mostly produced in Assam and some areas of bangladesh, i personally have not seen any particular unit to process ghost chili, But you can setup a common plant for all kinds of chili powders. If you can tell your desired capacity we can tell you the project cost.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Jack said on June 27, 2011
    please explain about the common plans available for drying the chili & powder. what short of machines required,land & capital investment or any trainings available....( i have tones of fresh ghost chili ) Or do you have any idea about Bhoot chili which i can export to other states or country ?
  • Shisham Jaiswal said on June 28, 2011
    Dear SOD, We are planning to establish one Flour Mill. We would like to know some basics about this :
    1. How much place (Pref. in Kattha/Sq.Ft/Bigha) does it require to establish one Atta Mill ?
    2. If the desired place is available, what are the secondary function to establish it as soon as possible ?
    3. How long will it take to complete the infrastructural work ?
    4. What kind of machine will be suitable for it ? What will be its cost ?
    5. What will be the productivity of the machine per day ?
    6. What will be the man power count to get the Atta from wheat ?
    7. Is it possible to get Besan, Sattu etc from that Machine ?
    8. Apart from Land what will be the approx cost of the entire Setup ?
    9. Any other Information related to that (For Ex. : Document requirement/ Permission Requirement).
    Hope to see a positive solution from your end as earliest. Shisham...... west bengal, hooghly
  • Amit Sharma expert adviser said on June 28, 2011
    @Shisham Jaiswal, Before answering your questions we would like know your desired capacity of the plant. Atta Mill Starts with 2 Ton/Hr of Production and ends nowhere. Secondly, Do you want to produce atta like Aashirwad, Pilsburry, Shakti Bhog, etc ? as the project cost differs for common and special chakki atta plant unit. Reply us with your desired capacity of atta you want to produce per day, we'll be more than happy to help you as soon as possible.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Amit Sharma expert adviser said on June 28, 2011

    @Jack, Do you want to process green chili or red chili ? And whats your desired capacity ?

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Amit Sharma expert adviser said on July 1, 2011
    @harshad agrawal, In this budget you can setup a perfectly feasible plant. You have a good budget to start a 4 Ton/hr Roller flour mill with 4 Ton/Hr Chakki Atta Plant. For the charges and other detail, you can mail me at the email id provided in my signature. We cannot disclose it in public.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Satish Chandra said on July 2, 2011
    How can establish a atta mill & oil mill in Uttar Pradesh.
    1. the investment 3 to 5 crore above.
    2. all government subsidy & facilities should be maintained.
    3. how much invest in machinery?
    4. how much invest installation of machine?
    5. how much moveable capital?
  • Amit Sharma expert adviser said on July 2, 2011
    @Satish Chandra, You can setup 6 Ton/Hr Roller Flour Mill. Proejct Cost - Rs. 3 Crores, Including Building, Godowns, Machinery and Electrical. And Rs. 2 Crores for working capital.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Ankush said on July 4, 2011
    hey Amit.. i would like to know the equipment list which can be used for the production of wheat only is that possible. Ankush 9888771200
  • Amit Sharma expert adviser said on July 7, 2011

    @Ankush, You want equipment list to produce wheat or the wheat products? i think you are just spamming here.

    @Santosh Gupta, What is the Brand of your manufacturing Company ?

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • SAMEER SANCHETI said on July 8, 2011
    i wish to start a maida mill in khamgaon city in buldhana district maharastra state so pls let me know regarding cost of project , it's feasibility & working know how
  • Amit Sharma expert adviser said on July 8, 2011
    @SAMEER SANCHETI, Please spare some time and read the comments posted here, You will find all the answers to your questions. Its not easy to post the same thing for each and every comment.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • rasheed ahmed said on July 10, 2011
    dear amit sharma. how much cost for 2Ton/Hr below detailed. machinery thanks
  • Amit Sharma expert adviser said on July 10, 2011
    @rasheed ahmed, Rs. 70 lakhs for 2 TPH.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Rahul Barpatre said on July 11, 2011
    Sir ,i am an engineering graduate, i am staying in Nagpur. I Want to start my own maida flour mill, in nagpur. I have near about 3600 sqft of land in nagpur will it be possible to start my business in this area, and if yes how much initial capital is required to start my business and and how can make contacts with the dealers of maida. sir please give me suggestion
  • Amit Sharma expert adviser said on July 11, 2011
    @Rahul Barpatre, To start a maida mill need area of 30000 SqFt. For invest and other details please read my previous posts here.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • anant jain said on July 11, 2011
    i'm want to start my own maide flour mill
  • SACHIN KHANDELWAL said on July 13, 2011
    i want to start our flour mill in jabalpur madhya pradesh please help mp. how can start flour mill. give me suggestion. sachin khandelwal jabalpur 9893269218
  • Amit Sharma expert adviser said on July 14, 2011
    @SACHIN KHANDELWAL, Whats your desired capacity of the plant? FYI, Most of the details are already provided here to start this business.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • P. N. RISHI said on July 15, 2011
    Sharma ji namskar , Pl.intimate me the break up of the estimated cost 2t/hr chakki fresh whole wheat atta plant as plant & machinery ,building cost working capital consultancy charges and thereafter maintenance charges etc. as i am looking for the plant at indust. area Bhagwanpur, Roorkee Distt. Haridwar U.K. INDIA PURUSHOTTAM
  • Amit Sharma expert adviser said on July 15, 2011
    The Whole wheat chakki atta plant with capacity of 2 ton/hour,In this plant you will only be able to produce chakki fresh atta and bran.

    Details are given below :
    Project : Chakkti Fresh Atta Plant
    Capacity : 2 Ton/Hour
    Approx Cost for Building : Rs.20,00,000
    Approx Cost for Machinery : Rs.35,00,000
    Approx Cost for Electrical :Rs.15,00,000
    Plant Erection Charges : Rs.3,00,000 ( Including Traveling Expenses for Erection labor )
    Consultancy and Designing Charges :Rs.2,00,000
    Boarding, Lodging and Traveling Charges For the Consultant(s) :To be paid by you.

    Covered Area Required for this Plant.
    Main Building - 2000 Sq. Ft.
    Raw Material Godown - 1500 Sq. Ft.
    Finished Godown - 2000 Sq. Ft.
    Raw Material : Wheat
    Finished Products : Chakki Atta 92% and Bran 8%
    Avg Profit - Rs 50/100 Kg.
    Power Required : 200 KVA
    Generator - 250 KVA ( If Power Problem is there)

    @P. N. RISHI, hope the details are clear.

    @shrikant shinde, Please post your desired capacity and budget.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • shrikant shinde said on July 15, 2011
    Hallo, I want to start the turmeric powder plant in maharashtra. So I want to know all about this plant. Is there any government subsidies for this plant? shrikant shinde.
  • neeraj arora said on July 19, 2011
    amit ji i m planning to start mini flour mill and mini rice sheller in my city .. kurukshetra(haryana). i have a space of 1.5 kanal.can u send me the detail estimate for other expenses ex.. machinery, ... just for mini plant ..thanks. please reply me on my mail
  • AShish said on July 19, 2011
    Hello Mr. amit i want start the floor mills at the location of unnao (up).that is the mid point of lucknow kanpur and allahabad. But i have no more capital so pls guide me which organization financed that particular project. and also to start its small scale.
  • Amit Sharma expert adviser said on July 19, 2011
    @AShish, Any Bank can finance this project ( 75% on plant and machinery , 60% on Civil Work).

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Amit Sharma expert adviser said on July 19, 2011

    @neeraj arora, 1.5 kanal = 8168 Sq. Ft. which is not sufficient to start a flour or rice mill. To start a feasible  flour mill u need 43560 Sq Ft i.e. 8 kanals and rice mill needs atleast double of that.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • satyendra yadav said on July 19, 2011
    gud evening amit ji, i am satyendra from etawah district,UP. sir i want to set up wheat mill abt 10 ton capacity per day,and also packing machine for 5, 10, 20 kg packet.my investment capacity 40 lac. so accordingly suggest the machine, cost, and and also guide if any subsidy is provided by the up government.
  • Mother Teresa Rural Development Society said on July 20, 2011
    We mother Teresa rural development society would like to know various types of machines and capacities in dal mill. could you send us the detail? Because we are going to start a unit in Narketpally village Nalgonda Disrtict - Andhra pradesh. It is to be managed by the Women Groups
  • John SEBAKARA said on July 20, 2011
    Hello, am a young man wishing to invest in maize milling. can you guide me in preparing a feasibility of the subject business that one can submit to the financial institution or donors for funding? What would be the benefit in general.
  • Amit Sharma expert adviser said on July 20, 2011
    @satyendra yadav, First of all 10 Ton/Day is not a feasible capacity to start a flour mill, Secondly Packing Machines for the packets of 5-20 Kg are more costlier than the plant project cost.So, i'll advise you to start a 2 Ton/Hr chakki fresh atta plant for which the details are already given in my previous posts.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Amit Sharma expert adviser said on July 20, 2011

    Mother Teresa Rural Development Society,  First you have to mention the name of Dal you want to process, Dal mill starts with the capacity of 2 Ton/Hr and ends no where.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Amit Sharma expert adviser said on July 20, 2011

    @John SEBAKARA, Please click/post here for any query related to corn/maize milling.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • SUKANTO DAN said on July 20, 2011
    I want to set up a atta chakki mill in purulia west bengal india establish cost 20tone per day
  • celestine jikeme said on July 22, 2011
    Please kindly do me a breakdown of what it will cost me in US Dollar, in terms of machinery required to set up a small scale milling plant for both wheat flour and spices,please include technical/consultancy cost.
  • abhijeet singh said on July 23, 2011
    want to buy china flour mill plant which can make atta maida suji
  • Amit Sharma expert adviser said on July 24, 2011
    Why do u want to buy china plant when you can get good machinery in india itself. Buying cheap machinery is not good for setting up a business.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • gopal said on July 24, 2011
    i want to start a flour mill business in porbandar, gujarat. i want to know that is this a right place for that kind of business and which type of machinery required for produce product like aata. maida. suji. capacity of less than 10 ton a day
  • ajaysharma said on July 25, 2011
    I want to start flour project of atta in ujjain & indore. Please suggest us how to start and which cost. please guide the same
  • Angyelile E Mkumbwa said on July 27, 2011
    I am looking for a business partner in Maize flour milling. I am based in Mbeya Tanzania,area with plenty of maize and currently there are no commercial Milling plant. Kindly connect me to interested partners in India.
  • srinivas.polisetti said on July 28, 2011
    please advise me I want to start a flour mill in small range. kindly give me mill capacity will choose for me. And give me apox. cost of machinery. thank you.
  • Shubham Aggarwal said on July 28, 2011
    @Amit Sharma, Sir I want to set a small scale Floor mill in Uttarakhand Distt Dehradun . So I would like to know all the Cost required to set the the plant and what things I have to keep in mind while setting up the plant. Also how the business prospective is their in Uttarakhand . Please Help..
  • Amit Sharma expert adviser said on July 28, 2011
    @Shubham Aggarwal, AND @rinivas.polisetti, read comment no. 210 and 199,186 and few of my comments in this article.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • deepak goyal said on July 29, 2011
    i want to start rice flour plant, could u help me in giving any project report related to this field. or else how can i start this plant, who r the clients, machinery required etc....
  • Amit Sharma expert adviser said on July 29, 2011
    @deepak goyal, First decide the capacity and type of rice mill you want to setup, Whether you want to setup a raw rice mill or a par-boiled rice unit. A feasible rice mill starts with 3 Ton/Hr and if you opt for 3 TPH raw rice mill the project cost is Rs. 70 Lakhs with indian machinery.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • tanay agrawal said on July 31, 2011
    sir, kindly elaborate the details n cost of machines required for chakki fresh atta plat. (in post 279 the amount u referred to as 35 lakhs).
  • Amit Sharma expert adviser said on July 31, 2011
    @tanay agrawal, What other details you want me to post ? Everything about chakki atta plant is explained in post no. 279

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Amit Sharma expert adviser said on August 2, 2011
    A 2 Ton/Hr Whole Wheat Chakki Atta Plant Machinery Including Electrical is Available for Sale. Good Condition, Good Price. If anyone is interested Feel free to Contact me.

    Amit Sharma (amitsharma@consultant.com)
    Milling Technologist

  • Sunil M said on August 3, 2011
    Dear Amitji, I do appreciate your efforts to enlighten each one of us over here for setting up of Flour mill. However I do have a small query with regards to same, I would like to know the difference between the Roller Mills and Chakki Mill Plants. Also do let me know if the Chakki Mill Plants can produce the same kind of whole Wheat Flour that the neighbor side chakkiwala produces.
  • arjun said on August 3, 2011
    i want to establish small chaki atta mill plant has been capacity 2000 to 3000 kg in day please tell me about detail and total investment

Your Comment

(All the above fields are required.)

Categories

Popular Articles

Join Our Newsletter